[ Pobierz całość w formacie PDF ]
(3) Take off sleve 10.
(4) Take off ring spring 9 with pawl for retaining ring.
(The removed ring spring 9 has to be corrected with plyer for fitting inside the sleeve 10 again.)
(5) Take off flat washer 10.
Sleeve 10
Ring spring 9
Flat washer 10
Spiral bevel gear 53
In the mounted situation, ring spring 9
has to be set inside sleeve 10.
Bearing box
Sleeve 10 and flat washer 10 have to be
set tight each other as per the above
illustration.
(6) Take off spindle complete with arbor press.
Hex socket head bolt M5x16
Arbor press
Set the bearing box with spiral bevel gear 53
and spindle on the widest U-form (width: 60mm).
Grease
Apply the grease SG No.0 in the gear housing by 50 g.
Remarks
The wheel cover of 5/8" can be used with this machine, if the flanged diamond wheel contacts
the original wheel cover.
The parts Nos are as follows.
No.163425-0 for 180mm (7") wheel
No.163424-2 for 230mm (9") wheel
Circuit diagram
Model 9077 and 9079, without soft starter
In some countries,
Noise suppressor is not
used.
Black
1
2
Noise
suppressor
1 Power
2
supply cord
Band
Switch
Motor housing
Lead wire from field has to be
guided through the hook.
Lead wires from field has to be set in the lead wire holders as per the
following illustration.
Noise suppressor
Lead wire from field has to be bound with a band
at the above illustrated positoin.
Circuit diagram
Model 9077S, 9077SL and 9079S, with soft starter
In some countries,
Noise suppressor is not
used.
Black
2 2
2
Switch
5
1 Power
1
supply cord
Band
White
Orange or Red
White
Soft starter Noise
circuit suppressor
Motor housing
Lead wire from field has to be
guided through the hook.
Lead wires from field and the same to soft starter circuit
have to be set in the lead wire holders as per the
following illustration.
Soft starter circuit
The lead wire to noise suppressor has to be
guided through the space between partition
and the rib.
Noise suppressor
(In some countries,
Lead wire from field has to be bound with a band
noise suppressor is not
at the above illustrated positoin.
used.) [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl fopke.keep.pl
(3) Take off sleve 10.
(4) Take off ring spring 9 with pawl for retaining ring.
(The removed ring spring 9 has to be corrected with plyer for fitting inside the sleeve 10 again.)
(5) Take off flat washer 10.
Sleeve 10
Ring spring 9
Flat washer 10
Spiral bevel gear 53
In the mounted situation, ring spring 9
has to be set inside sleeve 10.
Bearing box
Sleeve 10 and flat washer 10 have to be
set tight each other as per the above
illustration.
(6) Take off spindle complete with arbor press.
Hex socket head bolt M5x16
Arbor press
Set the bearing box with spiral bevel gear 53
and spindle on the widest U-form (width: 60mm).
Grease
Apply the grease SG No.0 in the gear housing by 50 g.
Remarks
The wheel cover of 5/8" can be used with this machine, if the flanged diamond wheel contacts
the original wheel cover.
The parts Nos are as follows.
No.163425-0 for 180mm (7") wheel
No.163424-2 for 230mm (9") wheel
Circuit diagram
Model 9077 and 9079, without soft starter
In some countries,
Noise suppressor is not
used.
Black
1
2
Noise
suppressor
1 Power
2
supply cord
Band
Switch
Motor housing
Lead wire from field has to be
guided through the hook.
Lead wires from field has to be set in the lead wire holders as per the
following illustration.
Noise suppressor
Lead wire from field has to be bound with a band
at the above illustrated positoin.
Circuit diagram
Model 9077S, 9077SL and 9079S, with soft starter
In some countries,
Noise suppressor is not
used.
Black
2 2
2
Switch
5
1 Power
1
supply cord
Band
White
Orange or Red
White
Soft starter Noise
circuit suppressor
Motor housing
Lead wire from field has to be
guided through the hook.
Lead wires from field and the same to soft starter circuit
have to be set in the lead wire holders as per the
following illustration.
Soft starter circuit
The lead wire to noise suppressor has to be
guided through the space between partition
and the rib.
Noise suppressor
(In some countries,
Lead wire from field has to be bound with a band
noise suppressor is not
at the above illustrated positoin.
used.) [ Pobierz całość w formacie PDF ]